Hacker News Reader

Comment by vidarh | Hacker News Reader

Electrical tape for complete blackout, and little small black dot stickers for LEDs you want to dim instead of completely cover.

For the black dot/circle stickers, just search for "black dot" on Amazon. The 6mm / 1/4 inch ones tends to fit neatly over most LEDs.

The electrical tape is easy enough to remove and reattach or replace for the rare occasion I actually need to see an indicator light.

I thought I'd need to remove it more often when I "snapped" and put electrical tape on every device in my living room a while back, but I've yet to remove a single bit of it. I'm sure I'll have to now and again, but it's worth the hassle.

View on HN

I sleep with a fan at night - when my fan from college finally died after a decade of use, I replaced it with a similar tower fan. It had a nice speed, timer function that went long enough for me to use the auto-shutoff as an alarm clock to avoid being jarred awake by an actual alarm. Oh, and it also had

FIVE, HUGE, BRIGHT BLUE LEDS WHICH WERE ON CONSTANTLY WHEN IT WAS RUNNING.

What idiot thought this was a good idea? Oh, and snipping them from the circuit also made sure the fan wouldn't work in high speed for some reason. So I had to solder a piece of wire from one end of the removed leds to the other.

My theory is that the prevalence of blue LEDs to this date is an after-effect of people who grew up back when blue LEDs were rare and expensive, and who came to see blue LEDs as a way of signalling higher value and who got used to wanting to put blue LEDs in everything for that reason long after the signalling effect was lost.

(it was first in the early 90's that bright blue LEDs became available, at least at reasonable price points)

I suspect there's a lot of truth in this.

This reminds me of going for an interview at Durham University in the early 80s. A professor in the physics department proudly showed me a prototype blue LED that they had developed. It was indeed quite a novelty at that time.

Ah, yes - a quick search confirms there was research in this area going on at the time: https://iopscience.iop.org/article/10.1088/0022-3727/16/6/02...

Undoubtedly I agree with both of you. Unfortunately, since the introduction of blue LEDs little thought has been given to the way people react to them. From my experience, they seem to raise the most criticism of all colored indicators.

Ha, I used to have a shirt draped around the neck of the fan for this exact reason. Didn't work too well, some of the light still bled through

I have an air filter with the same similarly bright blue LEDs. But, it has a night mode which you specifically have to enable each time where those are turned off. So the people who designed this thought of this problem and still wanted to have the overly-bright LEDs with no function. I don't quite understand.

I find that most tapes are not blacking out everything I want, and often light can leak through the cases of cheap equipment. For those cases I usually use a combination of tape (of any kind) with pieces of tin foil underneath, which reliably blocks all the light. Of course make sure to not use it on any contacts, but that's usually not an issue for consumer grade hardware.

I ended up putting some tape inside my Hue bridge to block out multiple bright blue LEDs. The cheap tape I used not blocking it completely (even with two or three layers) ended up working out pretty well - they're now _just_ bright enough to see if you need to check the status, but even in a dark room they won't catch your eye unless you're looking directly at them.

This! I also use electrical tape for complete blackout, and paper tape for dimming.

On a side note, also black electrical tape for laptop camera covering :)

Sound like it might also be an option to take a pin and poke a tiny aperture into the electrical tape over the lights you do want to see, only dim down.

That'd probably work fine too, but anywhere where I care about appearance I need to cut the electrical tape while the dot stickers are available in just the right size for fractions of a penny per sticker, so I have what appears to be a lifetime supply of stickers anyway.

I did this for LEDs, and I also took the opportunity to cover up all the logos on my electronics/appliances. It's nice having my home now be entirely free of Samsung/Sonos/Apple/Dell/etc. logos.

Took several different colours and types of tape to get everything looking nice.

Reply on news.ycombinator.com